007 First Light: Requirements and Settings for a Stable 60 FPS

Official System Requirements

IO Interactive has divided the requirements into five presets. They all require Windows 10 or 11 with a 64-bit system and an 80 GB SSD.

How to Read the Table

Three observations change the practical conclusions.

DLSS is not enabled in the first four presets. The figures for Minimum, Recommended, and Enthusiast are native-resolution results. This means the same graphics card will have noticeable headroom above the stated 60 FPS when upscaling is enabled, and that headroom is what turns an average of 60 into a stable 60 FPS.

The processor requirement barely changes. From Recommended through Enthusiast 2, it remains a Core i5-13500 or Ryzen 5 7600. Higher resolutions load the graphics card rather than the processor. For this game, investing in a top-end CPU just to reach 60 FPS does not pay off; the graphics card matters most.

VRAM requirements rise in steps: 6, 8, 12, and 16 GB. These are hard thresholds, not suggestions. At 1440p, an 8 GB card will run out of memory before it runs out of processing power, causing texture pop-in and stuttering rather than merely lowering the average FPS.

The Ultra preset needs separate context: the claimed 200+ FPS at 4K uses DLSS 4.5 with Dynamic Multi Frame Generation. This is different from native frame rate: generated frames make motion look smoother, but they do not reduce input latency the way real frames do.

Can My PC Run It? A Quick Check

If your processor predates a 9th-generation Core i5 or Ryzen 3000, start your check there: with a weak CPU, lowering the resolution will not help, and FPS will remain low even at minimum settings.

Settings for a Stable 60 FPS

The goal is not the highest average FPS, but keeping minimum frame rates close to 60. Follow these steps:

1. Enable upscaling. Use DLSS Super Resolution on NVIDIA graphics cards or FSR on AMD in Quality mode. This provides the largest performance gain with minimal loss of image quality and has been supported since release.
2. Do not use frame generation simply to reach 60 FPS. It works well when the base frame rate is already around 50–60 FPS. If the game runs at 35–40 FPS without it, motion will look smoother, but input latency will remain at the 35–40 FPS level.
3. Lower shadows and volumetric lighting. In games built on the Glacier engine, these settings create the heaviest load while making the least noticeable visual difference.
4. Set reflections to Medium, especially in scenes with water and glass.
5. Set texture quality according to available VRAM rather than raw performance. High-resolution textures have almost no FPS cost while they fit in memory, but cause a sharp loss of smoothness once they no longer do.
6. Cap the frame rate at or slightly below your monitor's refresh rate. The game supports an uncapped frame rate, but a stable rate feels smoother than one that constantly fluctuates.

Path Tracing and DLSS Ray Reconstruction will arrive in a post-release update. Enabling them will require a graphics card well above the Enthusiast tier, which is worth considering if you are planning an upgrade for this game.

Common problems and their solutions

• Stuttering when entering locations for the first time. This is typical of shader compilation. It usually disappears after the first pass through a scene and may improve after a driver update.
• Texture pop-in and frame drops at 1440p on an 8 GB card. This indicates a VRAM bottleneck, so lower texture quality.
• Low FPS with low graphics card utilization. This indicates a CPU bottleneck, so lowering graphics settings will have little effect. Check for demanding background processes.
• Crashes after a driver update. Reinstall the driver after completely removing the previous version.
• The game will not launch. Check that the Visual C++ packages are installed; common errors are covered in Visual C++ Redistributable for Games.

If Your Hardware Falls Short

When the graphics card falls below the Recommended tier and the processor is below a Core i5-13500 or Ryzen 5 7600, settings are no longer the answer. There are two options:

• Upgrade the graphics card if the platform is still current. For 1440p at 60 FPS, you need an RTX 4070- or RTX 5070-class GPU with 12 GB of VRAM. Which component to replace first and how much it costs in dirhams is explained in upgrading a PC in Dubai: what to change first.
• Buy a new machine if both the graphics card and processor need replacing. Ready-made configurations for your target resolution are available in the gaming PC catalog, while you can build your own in the configurator with compatibility checking.